Note: Nancy L. T. Hamilton and Bella Luloo Jewelry are NOT responsible for any injury, damage or health issues resulting from or even remotely related to these posts! You understand that you and only you are responsible for your decisions and actions! Take care and USE COMMON SENSE when working with any material or following any procedure that is even slightly a health risk!!!!!!!!!
Soldering and and the danger of fire, explosion and physical damage must be treated with respect and extreme caution. YOUR actions and improper use of materials and equipment can result in death or serious injury. Never work when mentally impared in any way and follow all safety precautions, manufacturer's instructions and the material's safety and data sheets. (What is MSDS?) There are multiple sources for finding MSDS sheets. Most companies have these sheets available. It is recommended that you check with the manufactuer before using any products that you are unfamiliar with or unsure of. Here is only one source for finding a variety of MSDS sheets: EHSO (Enviroment, Health and Safety Online). You can also check with OSHA - Occupational Safety and Health Administration - if you are unsure of safe practices.
.......................................................................................................................................................................................................................................................................................................................................................................................................
Setting up a soldering area
Prices as of 01-11-2010
So now I've scared you to death, right? Just remember to follow all safety precautions and to adhere to them religiously and you will embark on one heck of an exciting adventure! Good Luck!
Minimum materials:
1. Ventilation (VERY Inportant) - Now, I have a kitchen vent over my soldering area but when I started out I used an open window with a fan that had a reverse and forward air flow switch. Make sure that the air is being pulled OUT of your studio and away from your face!
2. Fire Extinguisher. (Also VERY important) - Make sure that it is of sufficient size for the area. Check with your local fire department if you are unsure.
3. A fireproof area to solder on. I use Durock to protect my walls and soldering surface. Durock is easy to cut (wear a mask - the product contains Crystalline Silica see MSDS sheet ). Durock is a gypsum board made with portland cement and aggregate. It is available at Home Depot or contact the manufacturer. I don't solder directly on the Durock but it is a non-flammable product that protects my wood and drywalled surfaces.
4. A soldering pad. There are MANY different types of soldering pads. I will only discuss what I use.
.png)
Charcoal Soldering Block - I work with the dense, close grained charcoal. I like it because it lasts longer and doesn't fall apart easily. Charcoal offers a heat-reflective surface, which means, that when you solder the heat from the torch is absorbed by the charcoal and reflected back onto the work. It is especially useful when soldering heavy pieces where you want to achieve an even heat. But, I use it for most soldering tasks. You can find one for about $8.00 at Rio Grande ($28.95-$49.95), Gesswein ( $7.65-$23.95), Otto Frei ($7.65-$29.95). Charcoal blocks can be shaped with burs and drill bits to create wells or divets to solder or melt metal in. I use several different blocks for different purposes.
Solderite Pad - Another type of soldering surface. This is also heat reflective, like the charcoal pad but it has the added advantage of having a surface that is soft enough to push soldering pins into (especially if you choose the soft variety). It can also be modified with burs and drill bits. Available at these and other locations: Rio Grande ($8.25-$21.25), Gesswein ($8.70-$23.35), Otto Frei ($8.25-$21.95).
Honeycomb Ceramic Block - This block dissipates heat away from your work. This can be very useful when you don't want a piece to overheat as when soldering small, delicate pieces. You can also find these at Rio Grande ($12.50 one size only), Gesswein ($9.80-$12.85) and Otto Frei ($9.95-$13.95).
Annealing pans and pumice. These are used for annealing your metal. I don't recommend them for straight soldering as its almost impossible to line up parts to be soldered. Also, small pieces (not to mention errant solder snippets) get lost in the rubble. Available at these stores and many others: Rio Grande ($28.95-$49.95), Gesswein ($30.60 - $65.60), Otto Frei ($28.95 - $54.95)
5. Torch, regulator, flash back arrestor, hose, torch tips. There are many different types and styles of torches. Your first decision is what type of gas and air mixture that you are going to use. I use Acetylene and air for most of my work. I chose this setup because it isn't as hot as an oxygen setup. I didn't want to teach soldering to new students and have them melting everything. It's a good trainer gas. I have been using it since day one and got used to working with it. I do use a small oxy/acetylene torch system for quick, hot solders. Rio Grande sells a Little Torch setup for small disposable tanks. It costs $239.00. You can also pick up a cheaper oxygen/mapp or propane gas setup at Sears. The product name and number is: OX2550 KC -Cutting, Welding and Brazing torch kit made by Bernzomatic.
Acetylene is a dirtier gas than propane but it is hotter. If you decide on propane, I advise that you choose to go with an oxygen and propane setup. Oxygen differs from air in that the oxygen is supplied by a tank. You need seperate regulators and hoses. The torch tip has both hoses coming into it and you need to balance the oxygen to the gas when you light it up. Its a little trickier than a plain acetylene/air setup. While the gas/air setup pulls the surrounding air into the torch and mixes with the gas there. No extra hoses or tanks are needed.
The oxygen type of torch burns very hot and is great for doing fast solder jobs where the whole piece doesn't get heated up. It is very useful when you want to make repairs or when you need to solder an item that has a heat intolerant item in the design.
Why am I using colors for propane, acetylene and oxygen? Well, the hoses are color coded and I thought I'd get you started on your training. Oxygen hoses are green and gas hoses are red! Always.
Tip: I recommend buying your torch in a kit. That way there is no guess work. Rio Grande and many other companies sell kits. Discuss any problems or questions regarding set-up with these vendors.
Precautions and safety procedures
One big rule, when choosing a torch head, is to NEVER use torch tips from another type or manufacturer in the handle. It can explode, catch on fire or other horrible things. This happened to me in jewelry class. The tips looked identical but were from another manufacturer. It even fit the torch body and screwed in easily. When I lit it a ball of fire burst out of the handle. If not for the quick thinking of another student, who shut off the gas main, I could be dead. Luckily, the flash was so fast, I didn't get burned. If you use different torches keep all the parts separate!
I recommend that you read the instructions that come with your torch, carefully. I buy my supplies and gas from Airgas and they were very helpful in teaching me all about setting up my torch and tanks. Soldering is safe if you follow the rules.
After you attach your hoses, torch handle, regulators, etc. to the tank, either purchase a commercial product for leak detection or mix up a very soapy mixture of water and dish detergent. I use a little water and a few big squeezes from the soap bottle. Don't make bubbles. Stir gently. Take a medium sized artist's paint brush and paint the soapy mixture all around the connections. If you see any bubbles forming, tighten the joints and re-check with soapy water. I clean off the soapy water after testing.
Another important step is to check your hoses for cracks and holes. I do this religiously every time I get a new bottle of gas. Occasionally, I will fill the sink with water and soap, turn on the torch and look for bubbles. You could use a bucket too. Never use plumbers tape to fix leaks. Have your regulators serviced and cleaned at least every few years - depending on the amount of use. I have an annual clean-up where I check the hoses in the sink (keep the torch head out of the water!), get the regulators spruced up and clean my tips with the tip brush. I have a back-up regulator for just this reason.
Keep the key, that turns on the gas, attached to the tank. It is important to be able to shut off your gas supply quickly and by leaving the key in place you will always know where it is. Tip: Don't forget to remove the key when you take your tanks in for a refill - they never get returned!
MORE LATER!
Charles Lewton-Brain (The Master) offers a more in-depth discussion of various soldering situations here at Ganoksin.
